Admin at 22:29, 28 January 2014

2014-01-28T22:29:25Z

Admin: Created page with "== '''Carrier Setup''' == The following steps are required to setup a new carrier 1. Decide on the type of signaling that will be used and configure it. (Click on the li..."

2014-01-28T22:11:16Z

Created page with "== '''Carrier Setup''' == The following steps are required to setup a new carrier 1. Decide on the type of signaling that will be used and configure it. (Click on the li..."

New page

== '''Carrier Setup''' ==

The following steps are required to setup a new carrier

1. Decide on the type of signaling that will be used and configure it. (Click on the links for more information on configuration, manuals etc.)
The following are supported:
a) [[SS7 - ITU/ANSI ISUP]]
b) [[ISDN]]
c) SIP/SIP-T

2. For E1/T1 connections, Sky Dance uses IP gateways to convert the PSTN signaling to SIP.

:Skynet offers the following fully integrated gateways

:For SS7 to SIP/SIP-T based on hardware from the following vendors:
:: a) [[Audiocodes Manuals|Audiocodes Mediant]] series gateways (Mediant 2000 - Mediant 8000)
:: b) Sangoma A10x series cards.

:For ISDN to SIP
:: a) Based on Audiocodes Mediant series gateways (Mediant 2000-Mediant 8000)
:: b) Sangoma A10x series based cards.

3. To configure a SS7 Carrier using Audiocodes gateways, there are several steps extra steps as follows:
a. [[Physical layer configuration|Configure the physical layer]] of the links and voice channels on the gateway. This is done via the Audiocodes element management system (EMS) or the Web GUI (M3K only).
b. [[Configure the originating point code|Next the E1/T1 originating point code]], [[Configure SS7 links|links]], [[Configure the linksets|linksets]] and [[Configure SS7 routes |routes]] must be configured via the EMS or Web GUI.
c. [[SS7#SS7_Stack|Configure the originating point code]], [[SS7#SS7_Linkset|links]], [[SS7#SS7_Linkset|linksets]] and [[SS7#SS7_Route|routes]] setup must be duplicated using the Sky Dance GUI. This will allow Sky Dance to control the gateway using M3UA and MGCP.

4. These steps are commont to SIP and SS7 Carriers
a. Setup the [[Translations#Partitions|partition]] for that carrier or reuse an existing one.
b. Setup [[Translations#Calling_Pre_Translation|pretranslation]] and/or [[Translations#Calling_Post_Translation|postranslation]] for the calling number if required.
c. Setup the [[Translations#Called_Pre_Translation|pretranslation]] and/or [[Translations#Called_Post_Translation|postranslation]] for the called number if required.
d. Setup an [[System#SIP_Proxy|inbound proxy]] if this is an inbound carrier or an System#SIP_Proxy|outbound proxy]] if this is an outbound carrier.
e. Setup the [[System#SIP_B2BUA|B2BUA]] which will handle the call.
f. For outbound carriers setup the [[Gateway_List|gateway list with the IP addresses of the terminating carrier's gateway(s).
g. [[Resource Groups|Add Resource groups]] for the voice circuits in the Sky Dance GUI.
h. Setup [[Routes|route lists]].
i. Setup [[Translations|translations]] and routing.

5. For SS7 Carriers this is the final step
a. [[SS7#SS7_CIC_Mapping|Configure the voice circuits]] to map the CICs to the resource group(s) just created.

← Older revision		Revision as of 22:29, 28 January 2014
Line 1:		Line 1:
		+	Click Here to return to the main Screen: '''[[Routing \|Back]]'''
		+
	== '''Carrier Setup''' ==		== '''Carrier Setup''' ==

Carrier Setup - Revision history

Admin at 22:29, 28 January 2014

Admin: Created page with "== '''Carrier Setup''' == The following steps are required to setup a new carrier 1. Decide on the type of signaling that will be used and configure it. (Click on the li..."